- 3 SWEEP SOFTWARE 2016 UPDATE
- 3 SWEEP SOFTWARE 2016 PATCH
- 3 SWEEP SOFTWARE 2016 CODE
- 3 SWEEP SOFTWARE 2016 DOWNLOAD
3 SWEEP SOFTWARE 2016 PATCH
Patch : account for additional modules, including those that failed after April 6th.īug Fix: patch in 9104, could fail on August 17th for some modules. Mitigation of potential damage caused by user attempting to use wrench to turn focus motor while powered on Reduce power consumption while switched off. Stability enhancements when updating over internal WiFi module. Reduce battery consumption while slewing. Reduced power consumption when power switch is off.īug fix: WiFi light was flashing when switch was off but battery charging.įixed buzzing sound when mount stationaryĪdded support for 3rd generation internal WiFi modulesīug Fix: Settings were reset to factory defaults if you plugged in the mount when it was switched offįeature: low battery warning on NS+ HC (requires 5.29.xxxx in the HC).īug Fix: Some mount were reporting the battery voltage/charge status incorrectly.įeature: If left plugged in indefinitely, the charger will keep the battery topped off. Tweaked Goto’s to make them more accurate Known bug: This version caused unexpected slews during alignment.īug Fix: Wifi config error introduced by īug Fix: Internal 3rd generation WiFi module caused SkyPortal to lock up when used with StarSense Accessory camera. Reduces power consumption during high speed slews.Ĭhanged default guide rate to 90% sidereal Reduce false alarms on RA and Dec sensors Known bug: this version caused unexpected slews during alignment. Reduced the drop error when doing a goto operation. Retuned feedback loop to reduce “buzzing” heard on some mounts.
3 SWEEP SOFTWARE 2016 UPDATE
Support for Hardware changes in AVX update (8pin header, K10 MCU etc.)īug Fix: Toggling up and down quickly causes anti-backlash to moved too far.īug Fix: Version number not reported correctly.īug Fix: With slew limits are disabled, you can’t slew east.īug Fix: Data corruption on SSA camera when used with internal Gen3 WiFiīug Fix: WiFi would lock up if user lost connection to WiFi attempted to reconnectīug Fix: Improved reliability of CFM updates over WiFiįeedback loop retuned to make slewing at rate 2-6 smoother.īug Fix: Tracking command sent during slew caused mount slew forever.īug Fix: A rare “No Response” error associated with the WiFi module.īundled with boot loader update which makes WiFi updates more reliable.īug Fix: USB to auxbus passthrough glitch Requires + of the NexStar+ HCīug Fix: AVX compatibility with newer HC firmware and possibly GPS. Reduced drop error at the end of a goto operation.īug Fix: Tracking now turns back on when you back away from a RA slew limit.įeature: When mount hits a slew limit it decelerates smoothly to a stopįeature: When mount hits a slew limit it posts a warning to a NexStar+ HC. Improves tracking slightly and slewing at rates 2 - 6.
3 SWEEP SOFTWARE 2016 DOWNLOAD
Download Celestron Firmware Manager (CFM)Ĭelestron recommends that you always use the latest version of the firmware in your devices The latest releases for CFM and this document can be found at URL below. This document covers only those devices whose firmware can be updated using Celestron Firmware Manager (CFM). It does not fully describe updates to boot loaders or databases.
3 SWEEP SOFTWARE 2016 CODE
This applies to the application code in our hand controllers, mounts, and accessories. If you hover your line back to the endpoint on the previous line, you'll notice a small gray dot appear.This page provides an overview of the changes to our firmware. Now I could continue creating lines just by left clicking anywhere, but I'm gonna show you a trick.
I'm gonna start by right clicking and selecting Create Line, hover over the center of the sketch and left click to start the line. What we're gonna do here is we're gonna create a path that we can sweep a profile along. I'm gonna right click and select New Sketch, and I'm gonna select the XY plane to sketch on. To begin, we need a blank part file, which I have open on the screen. In order to create a sweep, we need two things: we need a profile that's gonna be swept, and we need a path that it's gonna be swept along. We're now ready to look at the Sweep feature.